Wilkerson T12 Manual de usuario descargar pdf

Introduction

Follow these instructions when installing, operating, or servicing the product.

Application Limits

These products are intended for use in general purpose compressed air

systems only.

With Polycarbonate Bowl

kPa PSIG bar

Operating Pressure Maximum 1034 150 10.3

Operating Temperature Maximum 52°C (125°F)

Operating Temperature Minimum 0°C (32°F)

With Metal Bowl

kPa PSIG bar

Operating Pressure Maximum 1724 250 17.2

Operating Temperature Maximum 80°C (175°F)

Operating Temperature Minimum 0°C (32°F)

Note: The maximum recommended pressure drop for a particulate filter is

69 kPa (10 PSIG, 0.7 bar)

ANSI Symbol

Installation

1. The Filter / Regulator should be installed with reasonable accessibility for

service whenever possible – repair service kits are available. Keep pipe

or tubing lengths to a minimum with inside clean and free of dirt and

chips. Pipe joint compound should be used sparingly and applied only to

the male pipe – never into the female port. Do not use PTFE tape to seal

pipe joints – pieces have a tendency to break off and lodge inside the

unit, possibly causing malfunction. Also, new pipe or hose should be

installed between the Filter / Regulator and equipment being protected.

2. The upstream pipe work must be clear of accumulated dirt and liquids.

3. Select a Filter / Regulator location as close as possible to the equipment

being protected.

4. Install Filter / Regulator so that air flows in the direction of arrow on body.

5. Install Filter / Regulator vertically with the bowl drain mechanism at the

bottom. Free moisture will thus drain into the sump (“quiet zone”) at the

bottom of the bowl.

6. Gauge ports are located on both sides of the Filter / Regulator body for

your convenience. It is necessary to install a gauge or socket pipe plugs

into each port during installation.

Operation

1. Both free moisture and solids are removed automatically by the filter.

2. Manual drain filters must be drained regularly before the separated

moisture and oil reaches the bottom of the baffle or end cap.

3. The filter element should be removed and replaced when pressure

differential across the filter is 69 kPa (10 psig).

4. Before turning on the air supply, turn the knob counterclockwise until

compression is released from the pressure control spring. Then turn knob

clockwise and adjust regulator to desired downstream pressure. This

permits pressure to build up slowly in the downstream line.

WARNING

To avoid unpredictable system behavior that can cause personal

injury and property damage:

• Disconnect electrical supply (when necessary) before installation,

servicing, or conversion.

• Disconnect air supply and depressurize all air lines connected to

this product before installation, servicing, or conversion.

• Operate within the manufacturer’s specified pressure, temperature,

and other conditions listed in these instructions.

• Medium must be moisture-free if ambient temperature is below

freezing.

• Service according to procedures listed in these instructions.

• Installation, service, and conversion of these products must be

performed by knowledgeable personnel who understand how

pneumatic products are to be applied.

• After installation, servicing, or conversion, air and electrical

supplies (when necessary) should be connected and the product

tested for proper function and leakage. If audible leakage is present,

or the product does not operate properly, do not put into use.

• Warnings and specifications on the product should not be covered

by paint, etc. If masking is not possible, contact your local

representative for replacement labels.

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE

PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED

ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY

DAMAGE.

This document and other information from The Company, its subsidiaries

and authorized distributors provide product and/or system options for further

investigation by users having technical expertise. It is important that you

analyze all aspects of your application, including consequences of any

failure and review the information concerning the product or systems in the

current product catalog. Due to the variety of operating conditions and

applications for these products or systems, the user, through its own analysis

and testing, is solely responsible for making the final selection of the

products and systems and assuring that all performance, safety and warning

requirements of the application are met.

The products described herein, including without limitation, product features,

specifications, designs, availability and pricing, are subject to change by

The Company and its subsidiaries at any time without notice.

EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR

INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE

THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.

WARNING

Product rupture can cause serious injury.

Do not connect regulator to bottled gas.

Do not exceed maximum primary pressure rating.

WARNING

To avoid polycarbonate bowl rupture that can cause personal injury or

property damage, do not exceed bowl pressure or temperature ratings.

Polycarbonate bowls have a 150 psig (1030 kPa) pressure rating and a

maximum temperature rating of 52°C (125°F).

Adjustable Filter / Regulato

with Manual Drain

Installation & Service Instructions

83-954-000

1/4" and 3/8"

B12 Filter / Regulator Series, and

T12 Precision Filter / Regulator

ISSUED: May, 2005

Supersedes: November, 2003

Doc.# 83954000, ECN# 050500, Rev. 5

Richland, MI 49083 Tel: (269) 629-5000

CAUTION

Polycarbonate bowls, being transparent and tough, are ideal for use with

Filters and Lubricators. They are suitable for use in normal industrial

environments, but should not be located in areas where they could be

subjected to direct sunlight, an impact blow, nor temperatures outside of the

rated range. As with most plastics, some chemicals can cause damage.

Polycarbonate bowls should not be exposed to chlorinated hydrocarbons,

ketones, esters and certain alcohols. They should not be used in air systems

where compressors are lubricated with fire-resistant fluids such as phosphate

ester and di-ester types.

Metal bowls are recommended where ambient and/or media conditions are

not compatible with polycarbonate bowls. Metal bowls resist the action of

most such solvents, but should not be used where strong acids or bases are

present or in salt laden atmospheres. Consult the factory for specific

recommendations where these conditions exist.

TO CLEAN POLYCARBONATE BOWLS USE MILD SOAP AND WATER

ONLY! DO NOT use cleansing agents such as acetone, benzene, carbon

tetrachloride, gasoline, toluene, etc., which are damaging to this plastic.

Bowl guards are recommended for added protection of polycarbonate bowls

where chemical attack may occur.

1 2 3 4 5 6

Indice de contenidos

Pagina 1 - Adjustable Filter / Regulato

IntroductionFollow these instructions when installing, operating, or servicing the product.Application LimitsThese products are intended for use in ge

Pagina 2 - Service Kits Available

Lightly grease with provided lubricant.Inaspect for nicks, scratches, and surface imperfections.If present, reduced service life is probable and futur

Pagina 3 - Filtre et régulateur réglable

IntroductionSuivre ces instructions pendant l’installation, l’utilisation ou l’entretien du produit.Limites d’utilisationCes produits sont construits

Pagina 4 - Entretien

Appliquer un peu de la graisse fournie.Vérifier qu’il n’y a pas d’entailles, de rayures ni d’imperfectionssuperficielles. S’il y en a, la longévité e

Pagina 5 - Filtro / regulador ajustable

Introducción:Observe las siguientes instrucciones al instalar, operar o dar servicio al producto.Límites de aplicaciónEstos productos han sido diseñad

Pagina 6 - Servicio

Engráselo ligeramente con el lubricante suministrado.Verifique que no existen mellas, rasguños ni imperfecciones en lasuperficie. Si existen, es posi

Modelos relacionados B12

Comentarios a estos manuales

Sin comentarios

Wilkerson T12 Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Wilkerson T12. Wilkerson T12 User Manual Manual de usuario

Indice de contenidos

Modelos relacionados B12

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Wilkerson T12